Shop our Catalog Store in East Ridge, TN

Categories

Dock Accessories

← Prev
1 2
Next →
Sort by Alphabetical: Z to A
48 Per Page
  • Save 15%
Tie Down Washer Plate - 1-1/2"L X 5"H 24284
$8.22 $6.99
DOCK SYSTEM Washer Plate - Use 2 washer plates w/each angle. 1-1/2"L X 5"H. Part # 24284. MFG# 24284 UPC# 081628242843
70 item(s)
+ −
  • Save 15%
Tie Down T-Connector (Male) - 5"L X 5"H 26532
$41.16 $34.99
DOCK SYSTEM Male T-Connector - One welded 1/2" tab. Use w/female t-connector to attach fingers & ramps. Measures 5"L X 5"H. 3/4" bolt set (N) reuired for joint. Part # 26532. MFG# 26532 UPC# 081628265323
97 item(s)
+ −
  • Save 15%
Tie Down T-Connector (Female) - 5"L X 5"H 26528
$52.93 $44.99
DOCK SYSTEM Female T-Connector - Two welded 1/2" tabs. Bolts to side of dock to attach fingers & ramps 5"L X 5"H. Part # 26528. MFG# 26528 UPC# 081628265286
29 item(s)
+ −
  • Save 22%
Tie Down Pipe Holder/Outside - 3" 24280
$63.79 $49.99
DOCK SYSTEM Pipe Holder/Outside 3" - Bolts to outside of dock. Carriage bolt set (M) required for attaching. Use 2" pipe to hold dock in place. Part # 24280 MFG# 24280 UPC# 081628242805
26 item(s)
+ −
  • Save 15%
Tie Down Lag Bolt Set 24287
$18.81 $15.99
DOCK SYSTEM LAG BOLT SET Bolt and flat washer hot dip galvanized used to attach flotation drums to dock system. Part # 24287. MFG# 24287 UPC# 081628242874
49 item(s)
+ −
  • Save 15%
Tie Down Engineering Washer Plate Iniin 26409
$7.05 $5.99
I. Should be used with every Angle. Two required for each Angle. 1-1/2"L x 5"H. MFG# 26409 UPC# 081628264098
358 item(s)
+ −
  • Save 11%
TIE DOWN ENGINEERING Tie Down Engineering Dock Side Cross Beam Extension 86934
$39.19 $34.99
With the addition of the Cross Beam 28" Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam can be lengthened for use on docks that are six feet wide. MFG# 86934 UPC# 081628869347
1 item(s)
+ −
  • Save 10%
TIE DOWN ENGINEERING Tie Down Engineering Dock Side Cross Beam Extension 86916
$41.29 $36.99
With the addition of the Cross Beam 28" Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam can be lengthened for use on docks that are six feet wide. MFG# 86916 UPC# 081628869163
8 item(s)
+ −
  • Save 23%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Outside Corner End 26428
$70.49 $53.99
Commercial grade. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 12-1/4"L x 5"H For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26428 UPC# 081628264289
9 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Male T Connector 5L x 5H 26427
$54.11 $45.99
Commercial Grade w/ 3/4" tab. Use with Female T connector to attach fingers and ramps. Bolt set required for joint. Size: 5" x 5". For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26427 UPC# 081628264272
4 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Inside Corner 8-1/4L x 5H 2...
$68.22 $57.99
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ 3" holes. For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26417 UPC# 081628264173
22 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Inside Corner 8-1/4L x 5H 2...
$61.16 $51.99
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 8-1/4"L x 5"H w/ Square holes. For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26401 UPC# 081628264012
44 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Inside Corner 10-1/2L x 5H ...
$75.28 $63.99
Commercial grade. Should be used with one of the outside corners. Each leg has elongated holes for easy fit. 10-1/2"L x 5"H w/ 2-1/4" holes & larger brace. For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26424 UPC# 081628264241
22 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Galvanized Steel Piling Hoo...
$65.87 $55.99
Commercial Grade w/4" radius for 8" Piles. Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416). Size: 14" x 3" For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26429 UPC# 081628264296
51 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Backing Plate/Hurricane Str...
$21.16 $17.99
Standard grade for use with Piling Hoops. Size: 2" x 18" x 7 ga. For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26369 UPC# 081628263695
24 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Angle Brackets/Clip 26422
$14.11 $11.99
Commercial grade. Should be used for all cross supports. Each leg 2-3/4"L x 5"H. For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26422 UPC# 081628264227
27 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Angle Brackets/Clip 26399
$14.11 $11.99
Commercial grade. Should be used for all cross supports. Each leg 2-1/2"L x 2-1/2"H". For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26399 UPC# 081628263992
243 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Angle Brackets/Clip 26398
$24.69 $20.99
Commercial grade. Should be used for all cross supports. Each leg 3"L x 5"H. For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26398 UPC# 081628263985
193 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Angle Brackets/Clip 26397
$39.99 $33.99
Commercial Grade. Should be used for all cross supports. Each leg 4"L x 8"H For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26397 UPC# 081628263978
9 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Angle Brackets/Clip 26392
$14.11 $11.99
Commerical grade. Should be used for all cross supports. Each leg 2-3/4"L x 2-1/2"H. For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26392 UPC# 081628263923
56 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Angle Brackets/Clip 26380
$34.11 $28.99
Commercial grade. Should be used for all cross supports. Each leg 4"L x 7"H". For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26380 UPC# 081628263800
50 item(s)
+ −
  • Save 15%
TIE DOWN ENGINEERING Tie Down Engineering Dock Hardware - Angle Brackets/Clip 26379
$41.16 $34.99
Commercial grade. Should be used for all cross supports. Each leg 10"L x 3"H", 3 holes For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26379 UPC# 081628263794
15 item(s)
+ −
  • Save 23%
Tie Down Engineering Roller Only 26414
$130.39 $100.99
Heavy duty roller assembly. Bracket and roller bolt directly to the deck plate ( # 26416). An aid to the up and down motion of the dock in areas of tidal action. 6" roller turns on a 5/8" diameter shaft. 3/4" bracket is hot-dipped galvanized. CANNOT BE SOLD IN CALIFORNIA MFG# 26414 UPC# 081628264142
25 item(s)
+ −
  • Save 22%
Tie Down Engineering Pipe Holder Inkin 26411
$65.59 $50.99
K. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set ?M? required for attaching. MFG# 26411 UPC# 081628264111
41 item(s)
+ −
  • Save 23%
Tie Down Engineering Pile Chain Holder 26419
$194.39 $149.99
For use as a pile holder with 3/8" galvanized chain and shackles. Can be adjusted for various pile diameters. MFG# 26419 UPC# 081628264197
Out-of-stock
  • Save 22%
Tie Down Engineering O/S Corner Male 10 25491
$63.99 $49.99
B. One 1/2" welded tab. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set (N) or connector pin (O). Each leg is 10"L x 5" H. MFG# 25491 UPC# 081628254914
27 item(s)
+ −
  • Save 15%
Tie Down Engineering Male T Connector Inhin 26408
$44.69 $37.99
H. One welded 1/2" tab. Use with Female T connector to attach fingers and ramps. 5"L x 5"H. Bolt set "N" required for joint. MFG# 26408 UPC# 081628264081
146 item(s)
+ −
  • Save 22%
Tie Down Engineering Inside Rolling Ramp Dock Bracket 26431
$239.99 $186.99
5" x 11" x 1/4" galvanized steel bracket Includes left and right ramp brackets MFG# 26431 UPC# 081628264319
Out-of-stock
  • Save 22%
Tie Down Engineering Heavy Duty Inside Corner 3 Inein 26404
$118.29 $91.99
E. Should be used with one of the outside corners and has an internal pipe holder. 8-1/4"L x 5"H. Requires carriage bolt set "M" for attaching. MFG# 26404 UPC# 081628264043
8 item(s)
+ −
  • Save 28%
Tie Down Engineering Hd Plate Hoop Roller 26415
$411.99 $294.99
Piling hoop & roller intended for areas with a lot of wind, current or tidal action. Combines the Piling hoop (# 26412) and roller assembly (# 26414) to make up for the up and down movement. For pilings up to 12" in diameter. CANNOT BE SOLD IN CALIFORNIA. MFG# 26415 UPC# 081628264159
Out-of-stock
  • Save 30%
Tie Down Engineering Hd Plate Hoop Roller 14 In 26423
$363.29 $255.99
14" Commercial grade steel. The piling hoop secures around the piling, while roller permits smooth up and down movement. MFG# 26423 UPC# 081628264234
15 item(s)
+ −
  • Save 23%
Tie Down Engineering Hd Pipe Holder Hoop 26412
$185.19 $142.99
R & S. Heavy duty piling hoop for pilings up to 12" in diameter. The hoop is constructed of 1-1/2" pipe and is hot dip galvanized. It can be bolted directly to the side of the dock or to the optional deck plate. Commercial grade. MFG# 26412 UPC# 081628264128
Out-of-stock
  • Save 23%
Tie Down Engineering Hd Outside Corner (Female) Ina 26400
$78.99 $60.99
A. Two 1/2" welded tabs. Use with a male outside corner. Each leg is 10"L x 5"H. MFG# 26400 UPC# 081628264005
60 item(s)
+ −
  • Save 15%
Tie Down Engineering Hd Outside Corner (End) Incin 26402
$59.99 $50.99
C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners. Each leg is 10"L x 5"H. MFG# 26402 UPC# 081628264029
21 item(s)
+ −
  • Save 15%
Tie Down Engineering Hd Inside Corner Indin 26403
$67.05 $56.99
D. Should be used with one of the outside corners. Each leg has elongated holes for easy fit and is 8-1/4"L x 5"H. MFG# 26403 UPC# 081628264036
7 item(s)
+ −
  • Save 23%
Tie Down Engineering Hd Deck Plate 26416
$143.39 $110.99
Heavy duty roller assembly. Bracket and roller bolt directly to the deck plate ( # 26416). An aid to the up and down motion of the dock in areas of tidal action. 6" roller turns on a 5/8" diameter shaft. 3/4" bracket is hot-dipped galvanized. CANNOT BE SHIPPED TO CALIFORNIA MFG# 26416 UPC# 10081628264163
18 item(s)
+ −
  • Save 15%
Tie Down Engineering Female T Connector Ingin 26407
$61.16 $51.99
G. Two welded 1/2" tabs. Bolts to side of dock to attach fingers and ramps. 5"L x 5"H. MFG# 26407 UPC# 081628264074
81 item(s)
+ −
  • Save 15%
Tie Down Engineering Dock Hdw Lag Bolt 3/8X5 8/Bag 24292
$29.40 $24.99
Bolt and flat washer hot dip galvanized used to attach flotation drums to dock system. MFG# 24292 UPC# 081628242928
62 item(s)
+ −
  • Save 15%
Tie Down Engineering Dock Hdw Lag Bolt 3/8X3 8/Bag 24289
$21.16 $17.99
Bolt and flat washer hot dip galvanized used to attach flotation drums to dock system. MFG# 24289 UPC# 081628242898
37 item(s)
+ −
  • Save 21%
Tie Down Engineering Dock Hdw (N) Hex Head 8/Bag 24279
$66.19 $51.99
N. Includes lock nut. Used to connect male and female connectors. Galvanized 3/4" X 3-1/2". MFG# 24279 UPC# 081628242799
61 item(s)
+ −
  • Save 15%
Tie Down Engineering Dock Hardware M Carriage Bolt Set 8/Bag 26534
$23.52 $19.99
Used to attach A thru K component parts. 3/8 x 2-1/2" bolt flat washer and nut. Hot dipped galvanized. Commercial grade 1/2" x 3". CANNOT BE SOLD IN CALIFORNIA MFG# 26534 UPC# 081628265347
81 item(s)
+ −
  • Save 15%
Tie Down Engineering Dock Hardware Carriage Bolt Set 8/Box 26535
$58.81 $49.99
Used to attach A thru K component parts. 3/8 x 2-1/2" bolt flat washer and nut. Hot dipped galvanized. Commercial grade 1/2" x 3". MFG# 26535 UPC# 081628265354
45 item(s)
+ −
  • Save 23%
Tie Down Engineering Dock Hardware - Outside Corner/Male 10L x 5H 26418
$72.99 $55.99
Standard grade. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set or connector pin. Each leg is 10"L x 5" H. 1/2" Welded Tab. For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26418 UPC# 081628264180
3 item(s)
+ −
  • Save 23%
Tie Down Engineering Dock Hardware - Galvanized Steel Piling Hoop Commercial Grade 26394
$63.49 $48.99
Commercial Grade w/6" radius for12 Piles. Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416). Size: 18" x 3". For more dock hardware information including building guides, go to www.tiedown.com/adock.html MFG# 26394 UPC# 081628263947
Out-of-stock
  • Save 24%
Tie Down Engineering Dock Hardware - Galvanized Steel Piling Hoop Commercial Grade 26391
$56.39 $42.99
Commercial Grade w/5" radius for 10" Piles. Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416). Size: 16" x 3". For more dock hardware information including building guides, go to www.tiedown.com/adock.html . CANNOT BE SOLD IN CALIFORNIA. MFG# 26391 UPC#...
17 item(s)
+ −
  • Save 30%
Tie Down Engineering Dock Hardware - 14" Internal Pile Holder Commercial Grade 26434
$441.59 $310.99
Commercial grade. Heavy duty 1/4" galvanized steel. Bolts to the dock directly. 4 Rollers allow it to move smoothly up and down the piling. Size: 24" x 24" x 7-15/16". For more dock hardware information including building guides, go to www.tiedown.com/adock.html CANNOT BE SOLD IN CALIFORNIA. MFG# 26434 UPC#...
7 item(s)
+ −
  • Save 23%
Tie Down Engineering Chain Holder Injin 26410
$78.99 $60.99
J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/4", 3/8" and 1/2" chain. 5"L x 5"H. MFG# 26410 UPC# 081628264104
50 item(s)
+ −
  • Save 22%
Tie Down Engineering Chain Holder 26529
$62.49 $48.99
J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/4", 3/8" and 1/2" chain. 5"L x 5"H. MFG# 26529 UPC# 081628265293
38 item(s)
+ −
← Prev
1 2
Next →

Product filters

Price
 –   $
  • 5
  • 82
  • 158
  • 235
  • 311
Manufacturer
Advanced

Help

Have any questions on our products?  Feel free to contact us.